pmf-series ? p10gg-xxxxe(hxx)lf ? single output ? s ip12 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 p10gg-xxxxe(hxx)lf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications voltage range 10% input filter capacitors input reflected ripple current1 20 ma pk-pk output specifications voltage accuracy 2% short circuit protection indefinite (automatic recovery) line regulation 0.5% load regulation (0% - 100%) 0.5% (3.3vout models: 1.5%) ripple and noise (20mhz bandwidth) 75 mv pk-pk temperature coefficient 0.02% / c general specifications efficiency see table i/o isolation voltage (3 sec.) 1000 vdc (up to 5200 vdc optional*) i/o isolation capacity 60 pf, typ. i/o isolation resistance 1000 m ohm switching frequency 50 khz (typ.) humidity 95% rel h reliability calculated mtbf (mil-hdbk-217f) > 1.12 mhrs physical specifications case material non conductive black plastic (ul94v-0 rated) potting material epoxy (ul94v-0 rated) weight ~ 7.2g, typ. environment specifications operating temperature -25 to +71c (ambient) maximum case temperature 100c storage temperature -40 to +125c cooling free air convection rohs conform soldering 260c, max. (1.5mm from case 10s.) mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the pm f series p 10 g g - xxxxe (hxx) lf is a family of cost effective 2 w regulated single output dc/dc converters. these con verters are in an ultra miniature sip12 case. devices are encapsulated. hig h performance features: regulated output, 1000vdc up to 5200vdc i nput/output isolation, high efficiency operation, output voltag e accuracy of 2% maximum and input range of 10% tolerance. pmf-series 2 watt regulated single output sip 12 case 1 kv up to 5.2kv dc i/o isolation cont. short circuit protection rev.02-2009
pmf-series ? p10gg-xxxxe(hxx)lf ? single output ? s ip12 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # i n p u t v o l t a g e ( v d c ) i n p u t c u r r e n t n o l o a d ( m a ) i n p u t c u r r e n t f u l l l o a d ( m a ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 single output p10gg-053r3elf 5 70 515 3.3 500 64 330 p10gg-0505elf 5 70 606 5 400 66 330 p10gg-057r2elf 5 70 606 7.2 277.7 66 330 p10gg-0509elf 5 70 597 9 222.2 67 330 p10gg-0512elf 5 80 597 12 166.6 67 330 p10gg-0515elf 5 80 597 15 133.3 67 330 p10gg-0518elf 5 80 597 18 111.1 67 330 P10GG-0524ELF 5 80 579 24 83.3 69 330 p10gg-123r3elf 12 30 214 3.3 500 64 330 p10gg-1205elf 12 30 252 5 400 66 330 p10gg-127r2elf 12 30 252 7.2 277.7 66 330 p10gg-1209elf 12 45 248 9 222.2 67 330 p10gg-1212elf 12 45 248 12 166.6 67 330 p10gg-1215elf 12 45 248 15 133.3 67 330 p10gg-1218elf 12 50 245 18 111.1 68 330 p10gg-1224elf 12 50 245 24 83.37 68 330 p10gg-243r3elf 24 25 107 3.3 500 64 330 p10gg-2405elf 24 25 124 5 400 67 330 p10gg-247r2elf 24 25 124 7.2 277.7 67 330 p10gg-2409elf 24 25 122 9 222.2 68 330 p10gg-2412elf 24 25 122 12 166.6 68 330 p10gg-2415elf 24 25 122 15 133.3 68 330 p10gg-2418elf 24 25 120 18 111.1 69 330 p10gg-2424elf 24 25 120 24 83.3 69 330 if you need other specifications, please enquire. *options: h30 = 3000 vdc isolation h52 = 5200 vdc isolation for other i/o isolation please see table on the left hand side and add ? hxx ? before lf (p10gg-2412e h52 lf for 5.2kv) notes:
pmf-series ? p10gg-xxxxe(hxx)lf ? single output ? s ip12 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 package / pinning / derating 2.50 (0.10) 14.00 (0.55) 8.00 (0.32) 3.05 (0.12) 0.30 (0.01) peak modelcode datecode 1 12 32.00 (1.26) 27.94 (1.10) 2.54 (0.10) 0.50 (0.02) 3.40 (0.13) 0.68 (0.03) 0.50 (0.02) 3.40 (0.13) all dimensions are typical in millimeters (inches). - pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. # single single 3kv 1 +vin +vin 2 n.c. - vin 3 n.c. n.c. 9 n.c. n.c. 10 - vout - vout 11 +vout +vout 12 - vin n.c. pin connections app notes: 1 = measured input reflected ripple current with a simu lated source inductance of 12uh. 2 = tested by minimal vin and constant resistive load.
|
